|
|
|
 |
| Programmering av lysdiodsekvenser |
| Programvaran för styrning av lysdiodsystem ger möjlighet att utforma, provköra och ladda ner färgsekvenser från en PC till TridonicAtcos RGB-styrmoduler LED 0025 K211 och LED C003. |
| more info » |
|
|
|
| LED-Tool V4.1 |
| The LED Tool program has been developed for designing and costing the backlighting of illuminated lettering and symbols with TALEXX products from TridonicAtco.
The program is designed to achieve the most uniform backlighting. The calculated number of modules is based on empirical values and should be seen as a minimum guide value and not as an absolute value. The degree of transmission of the covering to be backlit is not taken into account in the calculation. |
| more info » |
|
|
|
| configTOOL V1.5 (Windows, 1.9 MB) |
| configTOOL is a further development of DALItool and is used to put DALI circuits into operation via a PC. This software also enables device-specific values to be set via DALI. configTOOL supports, among other things, DALI TOUCHPANEL (24035465), EMpro emergency lighting equipment and PCA T5 EXCEL one4all lp.
To connect the PC a DALI USB interface (24138923) and a DALI Power supply e.g. DALI PS1 (24034323) have to be used. The DALI-SCI (24033463) will not be supported. |
| more info » |
|
|
|
| masterCONFIGURATOR V1.22 |
| This software enables device-specific values of the DALI-MSensor, DALI animeo interface and DALI MC to be set via DALI. The DALI USB interface (24138923) must be used for the connection. DALI-SCI (24033463) is not supported. |
| more info » |
|
|
|
| corridorFUNCTION CONFIGURATOR |
| The corridorFUNCTION CONFIGURATOR is a simple software tool to activate and to adjust individual settings of the corridorFUNCTION in the digital dimmable PCA EXCEL one4all ballasts. To connect the PC a DALI USB interface (24138923) and a DALI Power supply e.g. DALI PS1 (24034323) have to be used. The DALI-SCI (24033463) will not be supported. |
| more info » |
|
|
|
| pcaCONFIGURATOR |
| The pcaCONFIGURATOR is a simple software tool to adjust individual PCA EXCEL one4all lp settings e.g. DC-level, DALI MEMORY, backwards compatibility, fastest fade times etc. To connect the PC a DALI USB interface (24138923) and a DALI Power supply e.g. DALI PS1 (24034323) have to be used. The DALI-SCI (24033463) will not be supported. |
| more info » |
|
|
|
| em-LINK Software |
| Up to five e-touchPANEL networked via Ethernet and therefore up to 600 DALI emergency lighting units can be easily monitored with em-LINK from a PC with a standard browser installed.
With em-LINK the data of all the connected e-touch subsystems can be collected, condensed into standard reports and saved or printed. |
| more info » |
|
|
|
| EMpro Ident. TOOL V1.0 (JAVA mobile phones, 20 kB) |
| The EMpro identification tool helps put up EM PRO EZ into operation in a DALI circuit. The tool is used to convert the binary LED identification signal into a DALI address and can be installed on JAVA-enabled mobile phones. |
| more info » |
|
|
|
| Payback® (Windows, 800 kB) |
| Med programmet Payback® kan TridonicAtco nu erbjuda ett lättanvänt program som förutom kapitalkostnaden också tar hänsyn till driftskostnad och energibesparingar, så att det slutresultat du kommer fram till avspeglar alla aspekter. Payback® är mycket användarvänligt och kan lätt utnyttjas även av nybörjare. Den enkla inmatningsskärmen fastlägger de viktigaste nyckeldata. |
| more info » |
|
|
|
| winDIM® 4.0e (Windows, 305 kB) |
| Med det nya winDIM®-programmet erbjuder TridonicAtco användarvänlig programvara för direktstyrning av belysningsscener via PC. Programmet förutsätter att armaturerna är försedda med digitalt dimbara driftdon från TridonicAtco. |
| more info » |
|
|
|
